Waterworks R.W. Atlas Two Hole Bridge High Profile Kitchen Fa Manuel d'utilisateur télécharger pdf

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST

RW ATLAS

Two Hole Kitchen Mixer with Spray

INSTALLATION GUIDELINES

Page 1 of 2

8.13.2012

These guidelines have been prepared for the professional contractor to aid in the installation of:

RW ATLAS TWO HOLE KITCHEN MIXER WITH SIDE MOUNT LEVER HANDLES AND SPRAY

(STYLE # RWKM10).

All dimensions are based on original specification and are subject to change and variation.

Please consult your Design Associate for current specifications.

SEE SERVICE PART DOCUMENT FOR PART ORDERING, AVAILABLE ON WATERWORKS.COM

Side Mounted Metal Lever Handles

Style No. RWKM10

SPECIFICATIONS:

Fitting Hole Diameter: 1-3/8"

Handle Spread: 8" [NOT ADJUSTABLE]

Inlet Connection Size: 3/8"

Inlet Connection Type: Female Straight

Maximum Deck Thickness: 1-1/2"

Minimum Deck Thickness: 1/4"

Recommended Water Pressure: 45psi

Spout Reach: 10"

Spout Swivel: Yes

IMPORTANT:

¾ NOTE: The screws on the top of the handles are

aesthetic and do not serve any mechanical purpose

and should not be removed.

¾ To ensure this product is installed properly, you

must read and follow these guidelines.

¾ The owner/user of this product must keep this

information for future reference.

¾ Be sure your installation conforms to federal state,

and local codes. In the State of Massachusetts, all

installations must comply with the rules and

regulations set forth within 248 CMR.

¾ This product must be installed by a professional

licensed contractor.

¾ Product should be on-site prior to rough-in. This

allows the installer to visualize the installation and

verify the center spread.

¾ Inspect this product to ensure you have all the parts

required for proper installation.

¾ Use only a strap wrench or protected/smooth-jaw

wrench on any finished surface.

¾ DO NOT use putty on deck fittings. Upper and lower

washers are provided.

SPOUT INSTALLATION:

¾ See Figure 1. for Steps 1-3.

1. Remove the rubber washer, plastic washer & nut

from both of the spout assembly's threaded shanks.

Note: The inlet tube may need to be unthreaded and

removed in order to remove nut.

2. Place the spout assembly through both holes in the

deck, along with the supply hoses and spray outlet

hose.

3. Re-install rubber washer, plastic washer and nut

from under the deck. Tighten the nut up against the

bottom of the mounting surface to secure the spout

assembly.

Figure - 01

SPOUT

ASSEMBLY

RUBBER

WASHER

PLASTIC

WASHER

NUT

AERATOR

HOT

SUPPLY

HOSE

COLD SUPPLY

HOSE

SPRAY OUTLET

SIDE SPRAY INSTALLATION:

¾ See Figure 2. for Steps 4-10.

4. Remove the nut and rubber washer from the bottom

of the threaded tube. Unthread the retaining collar

from the top of the threaded tube and remove the

plastic sleeve.

5. Loosen the hex collar and insert the threaded tube

along with the escutcheon and hex collar into the

hole in the deck, making sure the o-ring is between

the escutcheon and the deck.

6. Re-attach the rubber washer and nut to the

threaded tube from under the deck.

1 2

INSTALLATION GUIDELINES 1

Résumé du contenu

Page 1 - INSTALLATION GUIDELINES

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST RW ATLAS Two Hole Kitchen Mixer with Spray INSTALLATION GUIDELINES Page 1 of 2 8.13.2012 These guid

Page 2

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST RW ATLAS Two Hole Kitchen Mixer with Spray INSTALLATION GUIDELINES Page 2 of 2 8.13.2012 These guid

Commentaires sur ces manuels

Pas de commentaire

Waterworks R.W. Atlas Two Hole Bridge High Profile Kitchen Fa Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau Waterworks R.W. Atlas Two Hole Bridge High Profile Kitchen Fa. Waterworks R.W. Atlas Two Hole Bridge High Profile Kitchen Faucet, Metal Side Mount Levers and Spray User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour l'eau Waterworks R.W. Atlas Two Hole Bridge High Profile Kitchen Fa